Leysop Ltd.

+44 (0)1268 522111http://www.leysop.com

Request Information

Ultra-Fast Pockels Cell (UPC)

For most normal applications such as Q-switching and laser beam modulation, the standard EM500 and EM500M ranges of longitudinal Pockels cells are very adequate. Rise-times achieveable with these devices can be easily obtained in the range of 500ps and upward with suitable electrical drive waveforms.

Leysop Ltd Ultra-Fast Pockels Cell UPC

In fact in most systems, the rise time of the electrical pulse generator into the load capacitance of the cell is the dominant factor and typical risetimes are thus of the order of 3 to 5ns.

For some applications however, the shortest possible risetimes are required and this is where our UPC design excels. For pulse picking (that is selecting one or more adjacent pulses from a high repetition rate train of pulses, especially from a mode locked laser), the rise time requirements are usually based on generating a time gate of a few ns duration, so ~ns rise and fall times are adequate. However, with mode-locked sources often delivering pulse trains of greater than 100MHz repetition frequency shorter time windows are increasingly becoming more common.

For pulse slicing applications, the requirements are more stringent still. Not only are often very short (sub ns) pulses desired, but also the temporal shape of the optical pulse produced must be very clean with no overshot or ringing of the waveform. This requires a Pockels cell which is electrically well matched to the electrical driver source impedance across a wide frequency range. The capacitance of the Pockels cell is then of less importance as transmission line techniques must be used throughout the electrical system.

So what makes the UPC different from other Pockels cells? Well firstly, as mentioned above, the electrical parameters of the cell are matched to a 50W impedance as is to be expected to be found on most ultra-fast rise time drivers. This ensures that the waveform suffers no distortions due to electrical mis-match and cable reflections which could re-open the cell after a short time delay are minimised. Most Pockels cells which use a 50W r.f. type connector for the electrical interface are really only using this type of connector for the convenience (and often safety) which this imparts. For example, our EM500 series Pockels cells use HV BNC connectors which are rated at in excess of 10kV for continuous duty. The internal connections however present slightly too great a series inductance to truly match to 50W. That is not to say that for normal Q-switching duty the response is in any way detrimented by the electrical interface, only that when used for ultra-fast switching applications it is possible to resolve internal reflections on the sub-ns time-scale.

The solution used in our UPC is to use a slowly tapered electrode and matched body internal diameter to maintain the impedance as the small input electrical connection is enlarged to interface to the ring electrode of the KD*P crystal. By using this method, a clean electrical interface is presented to the driving circuit and internal reflections are minimised.

It is not however adequate to just ensure that the electrical pulse enters (and exits) the cell quickly. The dielectric constant of KD*P is very high (~50) and so the propagation of the electrical wavefront across the optical aperture is in practice relatively “slow”. Therefore there is a direct conflict between the requirements of fast switching and a large aperture and it is not possible to obtain ultra fast switching in large aperture cells. The UPC still provides a moderately large aperture of approximately 5mm which is obtained by use of a 6mm diameter crystal. This provides a good balance with rise-time which has been measured at <150ps by one of our customers in a “real world” application.

Leysop Ltd Ultra-Fast Pockels Cell UPC 2

Being made from KD*P, the Pockels cell has excellent transparency over the wavelength range of 0.3-1.2µm and thus is useable with almost all the most important lasers from the UV to the near infra-red. Of particular importance is the region centred at 800nm for use with Ti:Sapphire lasers. Obviously, as wavelengths increase, the voltage required for switching increases linearly and the driver power requirement therefore increases as the square of the wavelength. The cost of high voltage drivers scale at a very similar rate in practice, so techniques to reduce drive voltage are important to reduce system costs. One technique in common usage is to pass the laser beam through the cell twice, thus only requiring a quarter wave switching voltage instead of a half wave. There are obvious limitations to this technique for ultra-short pulse generation, but it may still be useful for pulse picking. A more generally useful approach uses a Pockels cell with two KD*P crystal mounted optically in series, but electrically in parallel such that each crystal only needs to operate to the quarter wave potential (around 3.6kV at 1064nm). Considering the difficulty of generating fast rise-time electrical drive waveforms, it is especially beneficial that the voltage requirements be minimised and therefore the UPC is available in both single and double crystal versions.

The link to the interface drawing for both these devices is below in pdf format.

For uses and applications of Pockels cells like the UPC, look in the Application Notes section then give us a call to discuss your requirements.

What’s new

  • Temperature Controlled Electro-Optic Modulator for Raman Spectroscopy

    Temperature Controlled Electro-Optic Modulator for Raman Spectroscopy

    Products | 17 Sep 2014

    For many years, Leysop have been providing custom and bespoke electro-optic systems for special applications.

  • Leysop Ltd Faraday Optical Isolators

    Faraday Optical Isolators

    Products | 27 May 2014

    The Faraday effect causes a rotation of the plane of light polarization when a light beam passes through a material in the presence of an axial magnetic field. The effect is similar to that produced when a light ray passes through an optically active material such as quartz

  • Leysop Ltd Ultra-Fast Pockels Cell UPC

    Ultra-Fast Pockels Cell (UPC)

    Products | 27 May 2014

    For most normal applications such as Q-switching and laser beam modulation, the standard EM500 and EM500M ranges of longitudinal Pockels cells are very adequate. Rise-times achieveable with these devices can be easily obtained in the range of 500ps and upward with suitable electrical drive waveforms.

  • Leysop Ltd - Miniature Pockels Cells for Laser Q-Switching

    Miniature Pockels Cells for Laser Q-Switching

    News | 23 May 2014

    The compact Pockels cell models EM508M-EM512M have for many years satisfied the needs of our customers for smaller (compared to the EM500 range) Pockels cells for OEM applications. With size constraints becoming ever tighter, we have developed a smaller model still, the EM510C.